This post has moved to our new site. Click on the photo or here to access: http://cleverquiltstudio.com/pre-cut-donut-quilt/
Hello Fellow Quilters!
Now that the My Sunshine quilt is completed are you ready to move on to our next project? Pay attention this one goes fast!
There is a fun trend out there called Jelly Roll Racing. What is it? Well, it is a way to create a quilt front in less than an hour. The basic idea is that you will open a jelly roll and then just sew all the strips together. This is what Roxy’s first quilt will be, but more on that in a bit.
While this quilt is fairly simple it can get confusing if you skip a step. Have your jelly roll handy? Let’s get started!
Step 1: Sew the Jelly Roll Together –
Simply sew one strip to the next. Don’t worry about the order of the strips it will make sense as we go. Just take the top one and work your way to the bottom. The method for stitching these together is exactly the same way we connect binding strips. Place the right sides together and stitch at a 45 degree angle. Make sure the small ends are facing to the right as we will be trimming these next. Alright time to stitch!
The idea is to chain stitch the bottom of one strip to the top of the next one.
Yes, you will have a lot of strips! Please excuse all the fuzzies. I would recommend a lint roller as well. I know we made good use out of it.
Step 2: Trim and Press –
Now that all of your strips are sewn together we need to trim them apart and cut the very large ‘dog ears’. Once you do this you should have one long ‘binding’ strip of fabric.
I know Baxter enjoyed the ‘dog ear’ confetti party.
Here is how the strip should look once they are pressed.
Step 4: Race Away, Connecting the Strip Together –
Pick one end and trim 18” or so. If you don’t do this all the angled seams will start to line up and it will not give you the variegated look desired. With right sides together you are going to sew the two ends of the strips together. Careful not to get any twists. Once you reach the end, (don’t panic, this is going to take a while) you will need to trim the loop part to create two flat ends. (See Roxy’s photos below for an example. Now, don’t get all up in arms the photo was purely for show. We laid it out and used a rotary cutter to make sure the edges were straight. )
Then, guess what? Yes, put the right sides together from the trimmed end and the other end you started and start sewing again! Note: YOU ARE MATCHING SHORT END TO SHORT END AND STITCHING LENGTHWISE. Don’t make a long tube, one side should always be open.
With each round you will repeat the trim and the ends together until you have your desired width of quilt. Each time gets half as long so the strips get shorter and shorter. Here is a rough video to show you:
You may want to wind a few bobbins ahead of time and watch every so often to make sure that you haven’t ran out of thread. It will happen my friends, just you wait.
After you have hit the desired width (the one below is ~48×60)you want you can proceed to spraying, pinning, quilting and binding or you can add a border, etc. It is completely up to you. But, let’s just take a moment shall we?! I mean how easy is this?! You don’t even have to decide how to arrange the fabric.
Now, I am making mine into a baby quilt for my dear friend Audra who got to say hello to her super healthy baby 3 weeks early! As you can see time is of the essence, but this quilt is too big for an everyday baby quilt.
After much deliberation with Roxy we decided that I could make three out of this one quilt, but how?! That, my friends, is next week’s post, but until then I will leave you with Roxy’s first ever quilting experience in slide show form! Seriously, how awesome is she! High-five first timer!
We almost did this entire quilt in a day too! (with only 1 or 2 sweat shop references…)
Until next week my friends! Have fun quilting!